SMART DRIVE ELECTRONIC WASHING MACHINE PHASE 1 to 5 – 230v
TABLE OF CONTENTS
SMART DRIVE ELECTRONIC WASHING MACHINE PHASE 1 to 5 – 230v
WHAT PHASE, SIZE & MODEL IS YOUR SMARTDRIVE?
TABLE OF CONTENTS
1.0 INTRODUCTION
1.1 HOW TO SERVICE SMARTDRIVE
1.2 SMARTDRIVE SERVICING – Quick Reference Guide!
2.0 SPECIFICATIONS
3.0 INSTALLATION
4.0 SMARTDRIVE COMPONENTS
4.1 Electronics Systems
4.2 Motor
4.3 Motor Controller Module
4.4 Display Module
4.5 Water Valves
4.6 Rotor Position Sensor
4.7 Pump
4.8 Inner and Outer Bowls
4.9 Lid Switch and Out of Balance Switch
4.10 Water Temperature Sensing
5.0 SMARTDRIVE INFORMATION
5.1 Favourite cycle (GW only) – All Phases
5.2 Customising Wash Cycles (GW only) – Phase 3 to 5 only
5.3 Delay Start (GW only) – Phase 2 to 5 only
5.4 Auto Water Level (GW only) – Phase 3 to 5 only
5.5 Water Saver (GW only) – Phase 3 to 5 only
5.6 Fabric Softener Dispenser – All Phases
5.7 Wash Performance Information – All Phases
6.0 SMARTDRIVE PROBLEMS
6.1 If Smartdrive Appears To Have No Power
6.2 If Smartdrive Powers Off mid cycle
6.3 Flooding
6.4 Leaking
6.5 Noisy
6.6 Continuous Spinning or Slow Spinning
6.7 Poor Wash Performance
6.8 Siphoning
6.9 Radio Frequency Interference (RFI)
6.10 Earth Leakage
6.11 It Appears Smartdrive is doing nothing
7.0 OPTION ADJUSTMENT MODE
7.1 Wash Water Temperature – All Phases
7.2 Rinse Options – All Phases
7.3 End of Cycle Warning Beeps (GW Only) – All Phases
7.4 Adjusting the Volume of Water Used in the Water Saver Option (GW only) – Phase 3 to 5
7.5 Auto Water Fill Level Adjustment (GW only) Phase 3-5
7.6 Out Of Balance Recovery Adjustment (GW and MW only) Phase 3-5
8.0 DIAGNOSTIC MODE
8.1 WHAT WAS THE LAST FAULT
8.2 TEST LID, OUT OF BALANCE, & SIZE SWITCHES
8.3 TO TEST PUMP & WATER VALVES
8.4 RESTART
8.5 RECYCLE
9.0 SIZE SETTING MODE – Phase 4 and 5 only
10.0 USER WARNINGS
10.1 Insufficient Hot Water (Hot Water LED flashing)
10.2 Insufficient Cold Water (Cold Water LED flashing)
10.3 No Water (Both Hot and Cold Water LEDs flashing)
10.4 Overloaded Product (High Water LED flashing)
10.5 Out of Balance (First Rinse or Final Spin and Current Spin Speed LED is flashing)
10.6 Suds (First Rinse LED is flashing or Final Spin LED is flashing)
10.7 Restart and Recycle (Wash Progress LEDs flashing)
10.8 Demonstration Mode (All LEDs flashing in patterns)
11.0 FAULT CODES
SMARTDRIVE PHASES 1 to 5 FAULT DESCRIPTIONS
12.0 MECHANICAL SERVICE SECTION
12.1 COMPLETE DISASSEMBLY
12.2 ASSEMBLY GUIDELINES
12.3 MOTOR ASSEMBLY & DISASSEMBLY
12.4 PUMP BLOCKAGE
12.5 SHAFT & BEARING REMOVAL
12.6 SHAFT & BEARING ASSEMBLY
Appendix A: Binary Decoding Chart – 8 Bits (0-255)
Appendix B: Technical Bulletins
WM011 ALTERNATIVE SPARE PARTS FOR PHASE 1 MOTOR CONTROLLER – June 1999
– Phase 1 only
WM013 PUMP HOOD KIT – January 2000 – Phases 2 to 5
WM51 DIAGNOSTIC FLOW CHART – Sept 1992– Phase 1 only
WM65 BIB DEFLECTOR – April 1994– Phase 1 only
WM70 PREMATURE OUT OF BALANCE – February 1995 – Phase 2 only
WM80 CONDENSATION KIT – May 1996 – Phase 2 & 3 only
WM81 PUMP SHIELD 5KG SMARTDRIVE – September 1996 - Phases 1 to 4
Appendix C: Smarttool
Appendix D: Tools for Servicing Smartdrive
Appendix E: IW SMARTDRIVE SERVICING
E.1 IW Quick Reference Guide
E.2 Specifications for IW
E.3 INTRODUCTION to IW
E.4 OPTION ADJUSTMENT MODE for IW
E.5 DIAGNOSTIC MODE for IW
E.6 SIZE SETTING MODE for IW
Download Here
diposting oleh James Priyono @ 01.27
3 Komentar
